NICE WINGO 5 Swing Gate Motor UAE

NICE WINGO 5 – Italian Engineered Long-Stroke 230V Swing Gate Automation for Leaves up to 3.5 Metres

The NICE WINGO 5, commonly supplied with WG5000 actuators, is an Italian 230V linear swing gate automation system for longer residential and compatible commercial gate leaves. Its longer stroke, robust thrust and MC800 control compatibility make it a practical step up from the WINGO 4 for larger gates.

Designed for professional automatic swing gate projects in the United Arab Emirates, NICE WINGO 5 can be integrated with a correctly matched control board, remote controls, safety photocells, warning light and access-control accessories. Final motor selection should always consider the physical gate, hinge condition, pillar geometry, wind exposure, opening angle and expected operating frequency rather than relying on gate weight alone.

WINGO 5 Features

• WG5000 linear operators for gate leaves up to approximately 3.5 m
• 230V AC motor with up to approximately 200W absorbed power
• Maximum thrust around 1700 N
• Maximum speed around 0.013 m/s
• Long-stroke actuator for longer leaves
• Nominal use rating around 30 cycles/hour in referenced data
• Mechanical travel-stop architecture depending kit
• Manual release for emergency access
• IP44 protection and -20°C to +50°C operating range
• Compatible with NICE MC800, OXI receiver, EPM photocells and NICE remote ecosystem
• Gate weight capacity reduces as leaf length increases; professional sizing is essential

WINGO 5 Technical Specifications

WINGO 5 Kit Includes

The following package contents are based on researched complete-kit configurations for this model or the corresponding manufacturer kit:

• 2 x NICE WG5000 swing gate motors
• 1 x NICE MC800 control unit
• 2 x NICE ON2E remote controls
• 1 x NICE OXI receiver
• 1 x Pair of NICE EPM / compatible BlueBUS photocells
• 1 x NICE flashing warning light
• 2 x Motor bracket sets

Kit contents may vary by market, stock package or manufacturer revision. Please confirm the exact supplied items before ordering, especially control boards, receiver models, remote-control types, foundation boxes or electric locks.

WINGO 5 Applications

• Large residential villa gates
• Long-leaf double swing gates
• Residential compounds
• Compatible commercial entrances
• NICE gate automation projects requiring MC800 and BlueBUS safety integration

WINGO 5 Supply & Installation Services

For reliable operation, the gate should move freely by hand before automation is installed. The hinges, stops, posts or pillars and mounting points should be structurally sound. Correct motor geometry is particularly important on swing gates because bracket position directly affects actuator travel, leverage, opening angle and the load placed on the motor.

A professional installation normally includes motor and bracket positioning, control-panel wiring, limit or travel setup, remote-control programming, safety-photocell alignment, automatic-closing configuration where required, force or torque adjustment, manual-release testing and final commissioning. Electrical installation should follow the manufacturer's instructions and applicable site requirements.

NICE WINGO 5 Compatible Accessories & Access Control

Depending on the selected NICE control board and product revision, NICE WINGO 5 can be combined with compatible accessories such as:

• Manufacturer-compatible remote controls and radio receivers
• Infrared safety photocells and other supported safety devices
• Flashing / warning lights
• Push buttons and key switches
• GSM gate openers and dry-contact mobile access controllers
• Keypads, RFID readers, intercom systems and access-control relays
• Electric locks where required by gate length, wind load or manufacturer guidance
• Battery backup or low-voltage accessories where supported by the exact 24V control system

Accessory voltage, input type and radio compatibility should be checked before connection. Do not assume that an accessory from the same brand is compatible with every controller generation.

Why Choose NICE WINGO 5?

NICE WINGO 5 is suitable for customers looking for a model-specific NICE swing gate automation solution with documented technical parameters, established control electronics and the ability to integrate safety and access-control equipment. Its selection should be based on the actual gate dimensions and usage profile so the motor operates with an appropriate mechanical margin rather than continuously at its maximum limit.

Why Choose Us – Sliding Gate Motor UAE

• Technical assistance to match the motor with gate leaf length, weight, hinge geometry and expected usage
• Support identifying compatible control boards, remotes, photocells and access-control accessories
• Professional installation, programming and testing services subject to project location and availability
• Gate automation products and spare-part support for established international manufacturers
• Delivery support across the United Arab Emirates
• After-sales assistance for compatible automation equipment and system setup

WINGO 5 FAQs

What gate is NICE WINGO 5 suitable for?

NICE WINGO 5 should be selected according to gate leaf length (Up to approx. 3.5 m), hinge position, opening angle, wind loading, gate construction and expected daily usage. Published capacities assume a correctly aligned, freely moving gate and suitable installation geometry.

What power supply and control system does NICE WINGO 5 use?

The researched configuration uses 230V AC. The referenced control platform is NICE MC800. The exact board, transformer and accessory wiring should always be confirmed against the supplied product revision before installation.

What is included with the NICE WINGO 5 kit?

Researched complete-kit configurations commonly include 2 x NICE WG5000 swing gate motors, 1 x NICE MC800 control unit, 2 x NICE ON2E remote controls, 1 x NICE OXI receiver. Exact kit contents can vary by market, distributor and product revision, so the final supplied package should be confirmed on the quotation or order.

Can NICE WINGO 5 be opened manually during a power failure?

Yes, the researched NICE automation configuration provides a manual or emergency release arrangement. The release method differs by operator type, so the installer should demonstrate the correct procedure after commissioning.

Can NICE WINGO 5 work with photocells, remotes, GSM or access control?

Yes, when connected through the compatible NICE control system, the operator can be integrated with supported remote receivers, safety photocells, flashing lights, push buttons and access-control devices such as GSM controllers, keypads or intercom relays. Compatibility must be checked before wiring.

Is professional installation available for NICE WINGO 5 in the United Arab Emirates?

Professional installation, setup, programming and testing can be arranged subject to product availability, project requirements and location. Correct bracket geometry, gate condition, safety-device positioning and final force/travel settings are important for reliable operation.

Need Help with NICE WINGO 5?

For product selection, provide the gate leaf length, approximate gate weight, number of leaves, pillar and hinge dimensions, required opening angle, expected daily usage and clear photographs of the entrance. This information helps confirm whether NICE WINGO 5 is suitable and which control, safety and access-control accessories should be included.