BFT ELI AC A40 – Italian Underground 230V Swing Gate Automation for Discreet Architectural Installations
The BFT ELI AC A40 is an Italian underground electromechanical swing gate operator designed for projects where the automation should remain largely hidden below ground. It provides strong 230V drive, high torque and weather-resistant underground construction for large villa, architectural and compatible commercial gates.
Designed for professional automatic swing gate projects in the United Arab Emirates, BFT ELI AC A40 can be integrated with a correctly matched control board, remote controls, safety photocells, warning light and access-control accessories. Final motor selection should always consider the physical gate, hinge condition, pillar geometry, wind exposure, opening angle and expected operating frequency rather than relying on gate weight alone.
BFT ELI AC A40 Features
- Underground installation keeps the operator discreet beneath the gate hinge area
- Suitable for gate leaves up to approximately 4 m; shorter limits may apply without an electric lock
- 230V AC drive with high output torque around 350 Nm
- Opening angle up to approximately 120°
- Approx. 13-second opening time through 90° in referenced configuration
- Mechanical opening and closing stops
- Electronic clutch impact management
- Optional magnetic limit accessories depending configuration
- Manual release via lever/personal-key system
- IP67 underground protection
- Compatible with RIGEL 6 / ALENA SW2 control systems
BFT ELI AC A40 Technical Specifications
| Model | BFT ELI AC A40 |
| Installation Type | Underground swing gate operator |
| Motor Power Supply | 230V AC |
| Maximum Gate Leaf Length | Up to approx. 4 m* |
| Without Electric Lock | Typically up to approx. 2.5 m* |
| Output Torque | Approx. 350 Nm |
| Maximum Opening Angle | Approx. 120° |
| Opening Time | Approx. 13 seconds / 90° |
| Frequency of Use | Approx. up to 20 cycles/hour in referenced data |
| Travel Stops | Mechanical opening and closing stops |
| Impact Reaction | Electronic clutch |
| Manual Release | Lever / personal-key system |
| Protection Rating | IP67 |
| Operating Temperature | -20°C to +55°C |
| Control Units | RIGEL 6 / ALENA SW2 |
| Country of Origin | Italy |
Product Selection / Specification Note: Foundation boxes, drainage and electric-lock requirements must be confirmed for the actual gate and kit.
BFT ELI AC A40 Kit Includes
The following package contents are based on researched complete-kit configurations for this model or the corresponding manufacturer kit:
- 2 x BFT ELI AC A40 underground operators
- 2 x Compatible underground foundation boxes where supplied as complete kit
- 1 x BFT RIGEL 6 / ALENA compatible control panel
- 1 x Pair of safety photocells
- 1 x Flashing warning light with antenna
- 2 x BFT remote controls
- 1 x Push button
- Manual release components and mounting accessories
Kit contents may vary by market, stock package or manufacturer revision. Please confirm the exact supplied items before ordering, especially control boards, receiver models, remote-control types, foundation boxes or electric locks.
BFT ELI AC A40 Applications
- Premium villa swing gates
- Architectural entrances where visible actuators are undesirable
- Residential compounds
- Commercial gates requiring discreet underground automation
- Double-leaf gates with compatible foundation and drainage
BFT ELI AC A40 Supply & Installation Services
For reliable operation, the gate should move freely by hand before automation is installed. The hinges, stops, posts or pillars and mounting points should be structurally sound. Correct motor geometry is particularly important on swing gates because bracket position directly affects actuator travel, leverage, opening angle and the load placed on the motor.
A professional installation normally includes motor and bracket positioning, control-panel wiring, limit or travel setup, remote-control programming, safety-photocell alignment, automatic-closing configuration where required, force or torque adjustment, manual-release testing and final commissioning. Electrical installation should follow the manufacturer's instructions and applicable site requirements.
BFT ELI AC A40 Compatible Accessories & Access Control
Depending on the selected BFT control board and product revision, BFT ELI AC A40 can be combined with compatible accessories such as:
- Manufacturer-compatible remote controls and radio receivers
- Infrared safety photocells and other supported safety devices
- Flashing / warning lights
- Push buttons and key switches
- GSM gate openers and dry-contact mobile access controllers
- Keypads, RFID readers, intercom systems and access-control relays
- Electric locks where required by gate length, wind load or manufacturer guidance
- Battery backup or low-voltage accessories where supported by the exact 24V control system
Accessory voltage, input type and radio compatibility should be checked before connection. Do not assume that an accessory from the same brand is compatible with every controller generation.
Why Choose BFT ELI AC A40?
BFT ELI AC A40 is suitable for customers looking for a model-specific BFT swing gate automation solution with documented technical parameters, established control electronics and the ability to integrate safety and access-control equipment. Its selection should be based on the actual gate dimensions and usage profile so the motor operates with an appropriate mechanical margin rather than continuously at its maximum limit.
Why Choose Us – Sliding Gate Motor UAE
- Technical assistance to match the motor with gate leaf length, weight, hinge geometry and expected usage
- Support identifying compatible control boards, remotes, photocells and access-control accessories
- Professional installation, programming and testing services subject to project location and availability
- Gate automation products and spare-part support for established international manufacturers
- Delivery support across the United Arab Emirates
- After-sales assistance for compatible automation equipment and system setup
BFT ELI AC A40 FAQs
What gate is BFT ELI AC A40 suitable for?
BFT ELI AC A40 should be selected according to gate leaf length (Up to approx. 4 m*), hinge position, opening angle, wind loading, gate construction and expected daily usage. Published capacities assume a correctly aligned, freely moving gate and suitable installation geometry.
What power supply and control system does BFT ELI AC A40 use?
The researched configuration uses 230V AC. The referenced control platform is RIGEL 6 / ALENA SW2. The exact board, transformer and accessory wiring should always be confirmed against the supplied product revision before installation.
What is included with the BFT ELI AC A40 kit?
Researched complete-kit configurations commonly include 2 x BFT ELI AC A40 underground operators, 2 x Compatible underground foundation boxes where supplied as complete kit, 1 x BFT RIGEL 6 / ALENA compatible control panel, 1 x Pair of safety photocells. Exact kit contents can vary by market, distributor and product revision, so the final supplied package should be confirmed on the quotation or order.
Can BFT ELI AC A40 be opened manually during a power failure?
Yes, the researched BFT automation configuration provides a manual or emergency release arrangement. The release method differs by operator type, so the installer should demonstrate the correct procedure after commissioning.
Can BFT ELI AC A40 work with photocells, remotes, GSM or access control?
Yes, when connected through the compatible BFT control system, the operator can be integrated with supported remote receivers, safety photocells, flashing lights, push buttons and access-control devices such as GSM controllers, keypads or intercom relays. Compatibility must be checked before wiring.
Is professional installation available for BFT ELI AC A40 in the United Arab Emirates?
Professional installation, setup, programming and testing can be arranged subject to product availability, project requirements and location. Correct bracket geometry, gate condition, safety-device positioning and final force/travel settings are important for reliable operation.
Need Help with BFT ELI AC A40?
For product selection, provide the gate leaf length, approximate gate weight, number of leaves, pillar and hinge dimensions, required opening angle, expected daily usage and clear photographs of the entrance. This information helps confirm whether BFT ELI AC A40 is suitable and which control, safety and access-control accessories should be included.
